P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« on: January 15, 2008, 07:38:10 pm » |
|
Whare could one put a pump on an Xbow with a mounted sf underneath (think Guru)?
And the spot where the stock barrel is already taken.
thanks much.
|
|
|
|
|
Megamannt92
Webmaster
Level 4 Poster
Points: 100
Posts: 801
|
|
« Reply #1 on: January 15, 2008, 07:44:46 pm » |
|
I can honestly say I know nothing about the X-Bow whatsoever. =p
Cole?
|
|
|
|
P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« Reply #2 on: January 15, 2008, 08:24:21 pm » |
|
Ive already tried on the `Him` of the gun(s) but I want it to be internal...ish.
|
|
|
|
Aguineapig
Level 3 Poster
Points: 50
Posts: 269
The tard of the universe!
|
|
« Reply #3 on: January 15, 2008, 08:31:36 pm » |
|
I think you might have to use the "guru" approach, its the most effective and its relatively easy to do.
|
|
|
|
jwasko
Level 3 Poster
Points: 425
Posts: 242
|
|
« Reply #4 on: January 15, 2008, 10:25:11 pm » |
|
After inspecting a picture of the internals of a X-bow, the only empty internal space seems two be directly below the plunger chamber. It looks like enough room to install a fairly narrow pump, like an at2k's. You can still put the Splitfire on the outside of the shell, directly below this empty space.
|
|
|
|
P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« Reply #5 on: January 16, 2008, 09:29:06 am » |
|
O.K. thanks. The reason for the 2k is to alter the deseign, and not compleatly rip of Groove, and to have two long range shots...... ....or shoty load the 2k I think I might try Jwasko`s approach, just put the pump on the left hand side so it can still be accessible.
|
|
|
|
General Cole
General
Level 5 Poster
Points: 225
Posts: 1135
Nerf On!
|
|
« Reply #6 on: January 27, 2008, 12:03:40 am » |
|
Sorry I'm late. What do you need? And what is the actual mod requiring?
|
|
|
|
P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« Reply #7 on: January 29, 2008, 05:07:34 pm » |
|
Im trying to figure out where to put a 2k pump internally, with a sf underneath (think guru w/ 2k)
|
|
|
|
General Cole
General
Level 5 Poster
Points: 225
Posts: 1135
Nerf On!
|
|
« Reply #8 on: February 21, 2008, 01:33:15 am » |
|
I would make the 2K on the right side, looking down, and place the pump on the other side, with SF on bottom. If you want to replace the SF with a 2K, just make the cut differently. OR, cut down the 2K and make a square cut on the crossbow and seal it with some Plexi-Glass. Mount the flat 2K on that. OR just epoxy the internals to the side of the gun and call it good.
|
|
|
|
P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« Reply #9 on: February 22, 2008, 05:15:32 pm » |
|
If I ever get around to this, I think i will just put the 2k pump externally on the right side.
|
|
|
|
General Cole
General
Level 5 Poster
Points: 225
Posts: 1135
Nerf On!
|
|
« Reply #10 on: February 25, 2008, 07:22:53 pm » |
|
I have had a pump there before. But make sure it is easy to reach in a short amount of time.
|
|
|
|
P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« Reply #11 on: March 02, 2008, 02:04:39 pm » |
|
How did you ataych the sf onto the xbow on the btg? how sturdy is it?
|
|
|
|
General Cole
General
Level 5 Poster
Points: 225
Posts: 1135
Nerf On!
|
|
« Reply #12 on: March 02, 2008, 11:29:44 pm » |
|
E6000, and I can swing the gun by the SF without worry. Just put some on, put on some latex gloves, lick a finger and smooth it out.
|
|
|
|
P.C. III
Level 1 Poster
Points: 0
Posts: 32
|
|
« Reply #13 on: March 03, 2008, 04:59:19 pm » |
|
E6000? any more detailed instructions? pics?
|
|
|
|
General Cole
General
Level 5 Poster
Points: 225
Posts: 1135
Nerf On!
|
|
« Reply #14 on: March 06, 2008, 09:08:32 am » |
|
|
|
|
|
|
|