See other nerf sites! Nerf HQ | NerfX | Nerf Haven | Foam: Total war

Archived-FU
August 13, 2022, 04:19:17 am
Welcome, Guest. Please login or register.

Login with username, password and session length
News: SITE AND FORUM ARE MOVING!

PLEASE GO TO:

http://www.foamuniverse.com/forum/index.php

AND MAKE AN ACCOUNT!
 
  Home Help Search Staff List Login Register  

Magstrike Clip Mod (CPVC)


Pages: [1]
  Print  
Author Topic: Magstrike Clip Mod (CPVC)  (Read 2863 times)
Megamannt92
Webmaster
Level 4 Poster
*

Points: 100
Posts: 801



View Profile
« on: November 12, 2006, 03:27:40 pm »

Mag-Strike Clip Modification (CPVC)
Putting PVC in your Mag clips drastically increases the overall range and power of your Magstrike.

What you will need:

-Pair of needlenose plyers
-Butter knife
-Hot glue/Hot glue gun
-Flat screwdriver
-Sandpaper(maybe if you mess up)
-Hammer
-Pipecutter/Hacksaw
-CPVC Pipe


OK lets get started. Pick up your clip, take your plyers, pull out the AR sticks and then flip over the clip and bore out the other pieces of plastic in the back like so. Ok that was the obvious and easy part.


Now the PVC part. Ok turn your clip over and locate the small slit in the back (look at the pic)
Take a butter knife and slide it under the piece carefully, donít do it too fast otherwise you will break it(the plastic is very thin). All right now that is off you will see the bottom of the default barrels, flip it over to the top again now and use the flat screwdriver to separate the barrels from the side of the clip. Do it slowly and carefully if you break the outside of the clip it will be beyond help.....After that the barrels should come out rather easily....

Ok now you have a empty clip cut the CPVC pipes, you can make them a little longer than the original barrels. Now put the bottom flat piece that we removed earlier back on keep it pressed on a table so it stays even....Now hot glue the barrels in from the inside. There your done!† † † †


If for some reason the clip does not fit into the gun, sand the back of the clip until it fits into the gun.
« Last Edit: March 09, 2007, 10:09:05 pm by Megamannt92 » Report Spam   Logged

Share on Facebook Share on Twitter

General Cole
General
Level 5 Poster
*

Points: 225
Posts: 1135

Nerf On!


View Profile WWW
« Reply #1 on: November 17, 2006, 01:13:35 pm »

If you can, switch out the CPVC for brass, not bagging on CPVC (the only stuff I use), but brass is more versatile.
Report Spam   Logged
Megamannt92
Webmaster
Level 4 Poster
*

Points: 100
Posts: 801



View Profile
« Reply #2 on: November 18, 2006, 01:00:50 pm »

I don't have any brass....The PVC works pretty good i think..
Report Spam   Logged
General Cole
General
Level 5 Poster
*

Points: 225
Posts: 1135

Nerf On!


View Profile WWW
« Reply #3 on: November 19, 2006, 03:23:09 pm »

CPVC, there is a big difference.
Report Spam   Logged
dude mic ray
Level 1 Poster
*

Points: -2
Posts: 33



View Profile
« Reply #4 on: January 11, 2007, 07:34:21 pm »

nice how more range do you get on it








 afro
Report Spam   Logged
Duck_slayer
I'm all alone in arkensaw
Level 3 Poster
*

Points: 13
Posts: 251


HI


View Profile WWW
« Reply #5 on: January 11, 2007, 07:55:26 pm »

Just a heads up please try not to post in an old topic unless you have something important to say.† afro Also try to capitalize more.
Report Spam   Logged
Megamannt92
Webmaster
Level 4 Poster
*

Points: 100
Posts: 801



View Profile
« Reply #6 on: January 13, 2007, 01:58:19 pm »

Range? This adds maybe 10-20 feet.
Report Spam   Logged

Pages: [1]
  Print  
 
Jump to:  

This site has been created by Jonas R. Wasilco.
Some fourm elements have been inspired by C:DOS Abandonware.

Like this fourm? Get your own!

Bookmark this site! | Upgrade This Forum
SMF For Free - Create your own Forum


Powered by SMF | SMF © 2016, Simple Machines
Privacy Policy